PLUMBER
First Period
Start Test Entire First Period / All Sections 100 questions, 25 credits, randomized from 1389 questions Start Test Entire First Period / All Sections 40 questions, 10 credits, randomized from 1389 questions Start Test Section 1: Workplace Safety and Rigging - Safety Legislation, Regulations, and Industry Policy
- Climbing, Lifting, Rigging, and Hoisting
- Hazardous Materials and Fire Protection
- Pipe Trades Codes
- Electrical Safety
20 questions, 5 credits, randomized from 225 questions Start Test Section 2: Tools, Equipment, and Materials - Hand Tools
- Power Tools
- Welded Pipe and Fittings
- Plastic Pipe and Tube
- Threaded and Grooved Pipe
- Tube and Tubing
- Valves
- Hangers, Supports, and Fasteners
- Pressure Testing
- Pumps
20 questions, 5 credits, randomized from 549 questions Start Test Section 3: Metal Fabrication - Welding Safety
- Welding
- Brazing and Soldering
20 questions, 5 credits, randomized from 135 questions Start Test Section 4: Drawings and Specifications - Sketching and Drawing
- Single Line Drawing
- Drawing Interpretation
20 questions, 5 credits, randomized from 160 questions Start Test Section 5: Calculations - Applied Calculations
- Perimeters, Areas, Percentage, and Grade
- Volumes and Capacities
- Piping Offsets
- Matter, Density, and Relative Density
- Pressure and Atmosphere
- Principles of Electricity
20 questions, 5 credits, randomized from 320 questions Second Period
Start Test Entire Second Period / All Sections 100 questions, 25 credits, randomized from 1414 questions Start Test Entire Second Period / All Sections 40 questions, 10 credits, randomized from 1414 questions Start Test Section 1: Single-Family Dwelling, Drain-Waste-Vent (DWV) - Drainage Systems
- Venting Systems
- Water Distribution
- Plumbing Fixtures
20 questions, 5 credits, randomized from 247 questions Start Test Section 2: Heating Systems - Temperature and Heat Science
- Expansion and Contraction Control
- Heat Transfer Equipment
- Temperature and Heat Calculations
- Heat Loss Calculations
- Heat Emission Units
- Buoyancy
20 questions, 5 credits, randomized from 301 questions Start Test Section 3: Single-Family Dwelling Hydronic Systems - Hydronic Heating Systems
- Hydronic Heating Boilers
- Boiler Trim
- Circulators
- Hydronic Heating and Cooling Systems
- Mechanical Ventilation
20 questions, 5 credits, randomized from 283 questions Start Test Section 4: Specialty Piping - Plastic and Lined Piping
- Fiberglass Piping
- Iron and Glass Piping
- Alloy Piping
- Medical Gas Piping
- Specialty Pipe Joining
- Hot Tapping and Freeze Isolation
- Compressed Air Systems
20 questions, 5 credits, randomized from 250 questions Start Test Section 5: Drawings, Layout and Rigging - Trigonometry
- Multiple Pipe Offsets
- Orthographic Projections
- Piping Isometrics
- Drawing Specifications
- Drawing Views
- Grades and Elevations
- Rigging
20 questions, 5 credits, randomized from 333 questions Third Period
Start Test Entire Third Period / All Sections 120 questions, 30 credits, randomized from 621 questions Start Test Entire Third Period / All Sections 40 questions, 10 credits, randomized from 621 questions Start Test Section 1: Private Sewage Disposal Systems - Introduction to Private Sewage Disposal Systems
- Septic Tanks, Effluent Chambers, and Holding Tanks
- Approved Effluent and Sewage Treatment Components
20 questions, 5 credits, randomized from 61 questions Start Test Section 2: Plumbing Theory - Residential Drainage Waste, Vents, Sumps, and Backvalves
- Floor Drains, Gang Showers, and Washing Machines
- Island Vents, Vent Stacks, and Relief Vents
- Commercial Wet Vent Installations
- Potable Water Distribution Systems
- Water Heating Appliances and Hot Water Recirculation
- Pressure Reducing Valves and Booster Pumps
- Faucets and Flush Valves
- Plumbing Fixtures
- Builders Levels and Hot Tapping
20 questions, 5 credits, randomized from 246 questions Start Test Section 3: Hydronic Heating - Hydronic Radiant Heating and Heat Loss Calculations
- Introduction to Hydronic Radiant Heating Design
- Boiler Start-up and Servicing
20 questions, 5 credits, randomized from 65 questions Start Test Section 4: Gasfitting Theory - Sizing of Chimneys and Flues
- Air Supply
- Domestic Gas Fired Appliances
- Basic Electricity for Gas Appliances and Controls
- Electrical Circuits for Domestic Gas Appliances and Gas Controls
- Gas and Electrical Controls
- Propane Cylinders and Vaporization
20 questions, 5 credits, randomized from 151 questions Start Test Section 5: Trade Math and Science - Volumes, Capacities, and Surface Areas
- Square Roots, Piping Offsets, and Fitting Allowance
- Fixture Spacing
- Grades and Elevations
20 questions, 5 credits, randomized from 98 questions Fourth Period
Start Test Entire Fourth Period / All Sections 120 questions, 30 credits, randomized from 701 questions Start Test Entire Fourth Period / All Sections 40 questions, 10 credits, randomized from 701 questions Start Test Section 1: Private Water Supply and Water Treatment - Introduction to Private Water Supply Systems
- Pumps for Private Water Supply Systems
- Private Water Supply Pressure System Components
- Private Water Supply Pressure System Sizing
- Introduction to Water Treatment
- Impurities in Water
- Methods of Treatment and Equipment Installation
20 questions, 5 credits, randomized from 150 questions Start Test Section 2: Special Applications - Cross-connection Control Awareness
- Specialty Water Distribution Control Valves and Equipment
- Introduction to Residential Fire Sprinkler Systems
- Wet Standpipe and Dry Standpipe Fire Lines
- Swimming Pools and Spas
- Compressed Air Systems
- Medical Gas Piping
- Lawn Irrigation
20 questions, 5 credits, randomized from 171 questions Start Test Section 3: Drain Waste and Venting - Interceptors and Indirect Wastes
- Sewage Sumps, Receiving Tanks, and Dumping Stations
- DWV, Water Distribution, and Fixtures for Residential Installation
- Specialty Plumbing Fixtures
- Commercial Equipment Installation
20 questions, 5 credits, randomized from 102 questions Start Test Section 4: Gasfitting Theory - Low Pressure Gas Layout Including Venting and Air Supply
- 2-psi Gas Line Layout
- Customer Bulk Storage Tank Installation and Vaporizers
- Additional Flues and Vents
- Mid and High Efficiency Gas Fired Appliances
- Electrical Circuits and Controls for Commercial Gas Appliances
- Combustion Analysis and Heat Exchanger Testing
20 questions, 5 credits, randomized from 278 questions Interprovincial (Red Seal) Review Exam
Start Test All Periods / All Sections 125 questions, 31 credits, randomized from 3266 questions Start Test All Periods / All Sections (Half Size) 60 questions, 15 credits, randomized from 3266 questions
Copyright © 2024, Syzygy Research & Technology Ltd. All rights reserved.
Follow us; we're friendly!
