Welder Tests

 
First Period
START
TEST		 Entire First Period / All Sections 100 Questions 25 credits Randomized, from 570 questions
START
TEST		 Entire First Period / All Sections 40 Questions 10 credits Randomized, from 570 questions
 
START
TEST		 Section 1: Safety, Tools, Weld Faults, and OAW
  • Welder Apprenticeship Program Orientation
  • Safety Guidelines
  • Welding Safety
  • Hand Tools
  • Power Tools
  • Weld Faults
  • Oxy-fuel Equipment
  • Oxy-fuel Welding and Brazing
  • Oxy-fuel Cutting
  • Materials Handling
 20 Questions 5 credits Randomized, from 237 questions
START
TEST		 Section 2: SMAW, GMAW, FCAW, and SAW One
  • Shielded Metal Arc Equipment
  • Mild Steel Electrodes
  • Basic Joint and Weld Types
  • Gas Metal Arc Welding Equipment
  • GMAW Filler Metals, Shielding Gases, and Safety
  • GMAW, Equipment, and Troubleshooting
  • Flux Cored Arc Welding
  • Submerged Arc Welding
  • Shop Lab Practices SMAW Welds on Mild Steel
  • Arc Cutting and Gouging
 20 Questions 5 credits Randomized, from 223 questions
START
TEST		 Section 3: Trade Problems
  • Fractions
  • Decimals
  • Percentage and Ratios
  • Geometric Formulas
  • Metric and Imperial Measure
 20 Questions 5 credits Randomized, from 110 questions
 
Second Period
START
TEST		 Entire Second Period / All Sections 100 Questions 25 credits Randomized, from 665 questions
START
TEST		 Entire Second Period / All Sections 40 Questions 10 credits Randomized, from 665 questions
 
START
TEST		 Section 1: SMAW Two
  • SMAW Groove Welds on Grey Cast Iron
  • Production and Properties of Metals
  • Carbon and Alloy Steels and Alloy Steel Filler Metals
  • Metal Identification
  • Distortion
  • Hardfacing
 20 Questions 5 credits Randomized, from 191 questions
START
TEST		 Section 2: GTAW One, GMAW and FCAW Two
  • Introduction to GTAW Process
  • GTAW Electrodes, Filler Metals, and Shielding Gases
  • GTAW Equipment, Maintenance, and Troubleshooting
  • GTAW Welds on Mild Steel
  • Aluminum and Aluminum Welding
  • GTAW Welds on Stainless Steel
  • GMAW Welds on Aluminum
  • GMAW, SMAW, and FCAW Welds on Mild Steel Pipe
 20 Questions 5 credits Randomized, from 280 questions
START
TEST		 Section 3: Pattern Development and Drawing Interpretation
  • Introduction to Pattern Development
  • Geometric Construction
  • Basic Fabrication Layout Practice
  • Pipe Layout
  • Welding Symbols
  • Estimating
 20 Questions 5 credits Randomized, from 194 questions
   
Third Period
START
TEST		 Entire Third Period / All Sections 100 Questions 25 credits Randomized, from 293 questions
START
TEST		 Entire Third Period / All Sections 40 Questions 10 credits Randomized, from 293 questions
 
START
TEST		 Section 1: SMAW Three, GTAW Two
  • Stainless Steels
  • Nickel Alloys and Clad Steels
  • SMAW Welds and Oxy-fuel Cutting on Mild Steel
  • SMAW Welds on Mild Steel Plate and Pipe
  • GTAW Welds on Mild Steel Plate and Pipe
 20 Questions 5 credits Randomized, from 102 questions
START
TEST		 Section 2: Drawing Interpretation
  • Introduction to Drawing Interpretation
  • Structural Drawings
  • Piping Drawings
  • Pressure Vessel Drawings
 20 Questions 5 credits Randomized, from 91 questions
START
TEST		 Section 3: Trade Science
  • Non-destructive Testing
  • Destructive Testing
  • Metallurgy
  • Heat Treatment
  • Codes and Standards
 20 Questions 5 credits Randomized, from 100 questions
Interprovincial (Red Seal) Review Exam
START
TEST		 All Periods / All Sections 120 Questions 30 credits Randomized, from 1528 questions
START
TEST		 All Periods / All Sections (Half Size) 60 Questions 15 credits Randomized, from 1528 questions